| [solved] Wildfire 6.06 Maps seriously broken[message #248985]
|
Sun, 11 April 2010 11:14 
|
|
 Fozzie |
 |
Messages:183
Registered:April 2010
Location: Germany |
|
|
Hi everyone!
I've been enjoying the 1.13 Mod for quite a while now and thought I'd couple it with Wildfire for some new challenges.
I used Scheinworld's AllInOne-installer and the full version of Wildfire, new ini-file an vfs-config are up and running. So far as starting, playing and (ini-)tweaking are concerned, it works like a charm. With one exception: a lot of maps are broken, cluttered with random objects. Mostly those metal-thingies with the rags (laundry racks?), wirecages, tyre stacks a.s.o.
Omerta for example is completely f***ed up, with laundry racks lining the pond in the western area of A9 and most of the buildings are a mess. At least I assume there should be buildings because between the onslaught of random objects there are roof-tiles and furniture sticking out now and then.
A10 is the same, the underground level (rebel base) however is how it is supposed to be in WiFi. Drassen Airport was fine, but one of the farmland sectors was again heavily cluttered with junk objects.
That's by now all of the sectors I've tested. Removing the broken sector files from the WiFi-Data/Maps-folder puts them back to JA-original state and thus makes it at least playable, but honestly - where's the point in that? In some cases it nearly appears to be a mixup of original and new maps but I'm not sure about that.
What I did not try, was installing my old retail version of WiFi and copying the map files from there, cause I don't know which changes there might have been since the release.
I already googled my fingers off and searched some forums but did not find any occurances of this particular problem (but hey, that doesn't say much, I might be just dumb after all). I'm sure that I simply overlooked something quite obvious, so please make me feel embarassed by rubbing the ridiculously easy solution in my face... 
Thanks in advance!
Report message to a moderator
|
Staff Sergeant
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Re: Wildfire 6.06 Maps seriously broken[message #249269]
|
Tue, 13 April 2010 23:10 
|
|
| Scheinworld |
 |
Messages:959
Registered:December 2007
Location: Baltic Sea, Germany |
|
|
Hallo Fozzi,
FozzieI used Scheinworld's AllInOne-installer and the full version of Wildfire, new ini-file an vfs-config are up and running. So far as starting, playing and (ini-)tweaking are concerned, it works like a charm. With one exception: a lot of maps are broken, cluttered with random objects. Mostly those metal-thingies with the rags (laundry racks?), wirecages, tyre stacks a.s.o.
I've uploaded a "tilesetsmix_test.7z" file:
http://rapidshare.com/files/375517695/tilesetsmix_test.exe
Let's try it again in this way:
1. fresh install of JA2
2. Allinone9
3. German WF6.06-Mod (just extract it into the main folder of your JA2 install)
4. "tilesetsmix_test.7z" (extract it into the main folder of your JA2 install as well; updated Ja2_Options.ini file + VFS setup are already included!)
I hope it works. Good luck!
Best regards; Schein
[Updated on: Wed, 14 April 2010 01:06] by Moderator Report message to a moderator
|
|
|
|
|
|
|
|
|
| Re: Wildfire 6.06 Maps seriously broken[message #249298]
|
Wed, 14 April 2010 11:16
|
|
| Fozzie |
|
Messages:183
Registered:April 2010
Location: Germany |
|
|
Allright, I'll try it with a fresh installation. Won't be able to check it out before tomorrow, though. But I'll report the outcome as soon as possible. Thanks again!
[Updated on: Wed, 14 April 2010 11:16] by Moderator Report message to a moderator
|
Staff Sergeant
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Blog
Search
Help
Members
Register
Login
Home
